View FTLX8551E3_4407856.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FTLX8551 Product Specification - November 2007
Product Specification RoHS-6 Compliant 10 Gb/s 850nm XPAK Transponder FTLX8551E3/ FTLX8551E3S/ FTLX8551F3
PRODUCT FEATURES Hot pluggable XPAK MSA form factor Total power consumption: 2.2 W maximum RoHS-6 compliant (lead-free) Temperature range 0C to 70C Transmission distance of 300m Uncooled 850 nm VCSEL laser LC connector, multimode fiber Full duplex transmission mode Digital Optics Monitoring (DOM) Power supply: +5.0 V, +3.3 V, Adaptable Power Supply (APS: +1.2 V) XAUI electrical interface - 4 x 3.125 Gb/s Ethernet (FTLX8551E3/E3S) - 4 x 3.1875 Gb/s Fibre Channel (FTLX8551F3) Management and control via MDIO 2-wire bus APPLICATIONS Low profile version for front panel mounting 10GBASE-SR ,10G Ethernet 70-pin connector (FTLX8551E3/E3S) De-latch mechanism with low 1200-Mx-SN-I Fibre Channel extraction force (FTLX8551F3) (FTLX8551x3 only) PRODUCT SELECTION Application De-Latch Mechanism Ethernet Bail Release Ethernet Screw Mount Fibre Channel Bail Release
Part Number FTLX8551E3 FTLX8551E3S FTLX8551F3
(c) Finisar Corporation - November 2007 Rev. B
Page 1
FTLX8551 Product Specification - November 2007
I.
Pin Descriptions
Pin No. 17 18 19 20 21 22 23 9 Description Management Data I/O. Requires external 10 - 22 k pull-up to the APS on host. Management Data Clock Input Port Address Input bit 4 Port Address Input bit 3 Port Address Input bit 2 Port Address Input bit 1 Port Address Input bit 0 Link Alarm Status Interrupt Output. Open Drain Compatible Output with 10 - 20 k pull-up on host. Logic high = Normal Operation Logic low = Status Flag Triggered Reset Input. Open Drain Compatible Input with 22 k pull-up to APS internal to transponder. Logic high = Normal Operation Logic low = RESET Vendor Specific Pins. Leave unconnected when not used. TX ON/OFF Input. Open Drain Compatible Input with 22 k pull-up to APS internal to transponder. Logic high = Transmitter On Logic low = Transmitter Off Pulled low inside transponder through a 1 k resistor to Ground Reserved For Future Use Reserved For Future Use Module XAUI Input Lane 3- Module XAUI Input Lane 3+ Module XAUI Input Lane 2- Module XAUI Input Lane 2+ Module XAUI Input Lane 1- Module XAUI Input Lane 1+ Module XAUI Input Lane 0- Module XAUI Input Lane 0+
Signal Name Level I/O Management and Monitoring Ports MDIO Open Drain I/O MDC PRTAD4 PRTAD3 PRTAD2 PRTAD1 PRTAD0 LASI 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS Open Drain I 1 I I I I O
RESET
Open Drain
I
10
Vendor Specific TX ON/OFF Open Drain I
11,15,16,24 12
MOD DETECT Transmit Functions Reserved Reserved TX LANE 3- AC-coupled, TX LANE 3+ Internally biased differential TX LANE 2- XAUI TX LANE 2+ TX LANE 1- TX LANE 1+ TX LANE 0- TX LANE 0+
O I I I I I I I I I I
14 68 67 65 64 62 61 59 58 56 55
(c) Finisar Corporation - November 2007 Rev. B
Page 2
FTLX8551 Product Specification - November 2007
Pin Descriptions (continued)
Signal Name Level Receive Functions Reserved Reserved RX LANE 0+ AC-coupled, RX LANE 0- Internally biased differential RX LANE 1+ XAUI RX LANE 1- RX LANE 2+ RX LANE 2- RX LANE 3+ RX LANE 3- DC Power GND 0 V DC I/O O O O O O O O O O O Pin No. 38 39 41 42 44 45 47 48 50 51 1, 2, 3, 33, 34, 35, 36, 37, 40, 43, 46, 49, 52, 53, 54, 57, 60, 63, 66, 69, 70 7, 8, 28, 29 27 25 +3.3 V DC +5.0 V DC 5, 6, 30, 31 4, 32 26 13 Description Reserved For Future Use Reserved For Future Use Module XAUI Output Lane 0+ Module XAUI Output Lane 0- Module XAUI Output Lane 1+ Module XAUI Output Lane 1- Module XAUI Output Lane 2+ Module XAUI Output Lane 2- Module XAUI Output Lane 3+ Module XAUI Output Lane 3- Ground connection for signal ground on the module
APS APS SENSE APS SET 3.3 V 5.0 V Reserved Reserved
+1.2 V +1.2 V
Input from Adaptive Power Supply APS Sense Output. Connected to the APS input inside transponder. Feedback input from APS. Connected to GND through a 1180 resistor inside the transponder. DC Power Input, +3.3 V DC, Nominal DC Power Input, +5.0 V DC, Nominal Reserved for APD. Reserved.
(c) Finisar Corporation - November 2007 Rev. B
Page 3
FTLX8551 Product Specification - November 2007
Electrical Pad Layout
Figure 1 - XPAK Transponder Electrical Pad Layout
II. Absolute Maximum Ratings
Parameter Storage Ambient Temperature1) Operating Case Temperature1) Supply Voltage +5.0 V Supply Voltage +3.3 V Supply Voltage APS Static Discharge Voltage, All Pins2) Average Receive Optical Power
Notes: 1) 2) Non-condensing. HBM
Symbol TS TC V5 V3 Vaps STd RxP max
Limit Values min. max. -40 85 0 70 0 6 0 4 0 1.5 500 0
Unit C C V V V V dBm
Exceeding any one of these values may permanently destroy the device.
(c) Finisar Corporation - November 2007 Rev. B
Page 4
FTLX8551 Product Specification - November 2007
III. Electrical Characteristics
Recommended Operating Conditions
Parameter Operating Case Temperature1) Transponder Total Power Consumption Supply Voltage +5.0 V Supply Current +5.0 V Supply Voltage +3.3 V Supply Current +3.3 V Supply Voltage APS Supply Current APS
1)
Symbol TC P VCC5 ICC5 VCC3 ICC3 VCC aps ICC aps
min. 0 4.75 3.14 1.152
Values typ.
max. 70 2.2 5.25 190 3.47 72 1.248 850
Unit C W V mA V mA V mA
5.0 157 3.3 55 1.2 830
Worst case thermal location, see also Environmental Performance.
Electrical DC Characteristics
(VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C) Values Parameter Symbol min. typ. 1.2 V CMOS I/O DC Characteristics (PRTAD; LASI; RESET; TX_ONOFF) External Pull-up Resistor for Open Rpullup 10 Drain Output High Voltage2) Voh 1 Output Low Voltage2) Vol Input High Voltage Vih 0.84 Input Low Voltage Vil Input OFF Current3) Ipd -1 XAUI I/O DC Characteristics (TXLANE[0..3]; RXLANE[0..3]) Differential Input Amplitude (pk-pk) 4) Vin_xaui Differential Output Amplitude (pkVout_xaui pk) 4) MDIO I/O DC Characteristics (MDIO; MDC) Output Low Voltage5) Output Low Current Input High Voltage Input Low Voltage Pull-up Supply Voltage Input Capacitance Load Capacitance External Pull-up Resistance
2) 3) 4) 5)
max. 22 0.15 1.5 0.36 1 2000 1600
Unit
k V V V V A mV mV
160 800
VOL IOL VIH VIL VPU CIN CLOAD RLOAD
-0.3 0.84 -0.3 0.84
1.2
0.2 20 1.5 0.36 1.5 10 470
200
V mA V V V pF pF
Rpull-up = 10 k to 1.2 V. Vin = 1.2 V. AC coupled. IOL = 100 A.
(c) Finisar Corporation - November 2007 Rev. B
Page 5
FTLX8551 Product Specification - November 2007
Electrical AC Characteristics
(VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C) Values Parameter Symbol Unit min. typ. max. XAUI Input AC Characteristics (TXLANE[0..3]) Baud Rate RXAUIIN Gbit/s Fibre Channel 3.1875 Ethernet 3.125 Baud Rate Tolerance RTOLXAUI -100 100 Ppm Differential Input Impedance ZINXAUI 80 100 120 Differential Return Loss1) |S11| 10 dB Jitter Amplitude Tolerance3) JXAUITOL 0.65 UIp-p XAUI Output AC Characteristics (RXLANE[0..3]) Baud Rate RXAUIOUT Gbit/s Fibre Channel 3.1875 Ehernet 3.125 Baud Rate Variation RXAUIVAR -100 100 Ppm XAUI Eye Mask (far-end) According to IEEE and Fibre Channel Output Differential Impedance ZOUTXAUI 80 100 120 Differential Output Return Loss1) |S22| 10 dB Total Jitter4) TJXAUI 0.4 UI Deterministic Jitter4) DJXAUI 0.17 UI Power-On Reset AC Characteristics Power-On Reset and TX_ONOFF According to XENPAK MSA Issue 3.0 2002-9-18 Characteristics MDIO I/O AC Characteristics (MDIO; MDC) MDIO Data Hold Time tHOLD 10 Ns MDIO Data Setup Time tSU 10 Ns Delay from MDC Rising Edge to tDELAY 150 Ns MDIO Data Change MDC Clock Rate MAX 2.5 MHz
1) 2) 3) 4)
100 MHz to 2.5 GHz. At crossing point. Per IEEE Std 802.3ae. Far-end, measured values.
(c) Finisar Corporation - November 2007 Rev. B
Page 6
FTLX8551 Product Specification - November 2007
IV. Optical Characteristics
(VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C) Values Parameter Symbol Unit min. typ. max. Transmitter Launch Power in OMA1) PO-OMA -2.8 -1.5 dBm Average Launch Power1) PO-Avg -5 -1 dBm Center Wavelength Range1) C-Tx 840 850 860 Nm 0.4 0.45 Nm RMS Spectral Width1) I Extinction Ratio ER 3 5.5 dB Relative Intensity Noise12OMA RIN -128 dB/Hz Eye Mask Definition According to IEEE and Fibre Channel Encircled Flux EF at 19 m 86%, at 4.5 m 30% Optical Return Loss Tolerance ORLT 12 dB Average Launch Power of OFF PO-OFF -30 dBm Transmitter Receiver Stressed Receiver Sensitivity in OMA PIN-S -7.5 dBm Receiver Sensitivity in OMA2) PIN -11.1 dBm Average Receive Power PIN-max -1 dBm Signal Detect Deassert Level PSDL -14.5 dBm Signal Detect Assert Level PSD -18.0 dBm Signal Detect Hysteresis PSD 0.5 1.5 dB Receiver Reflectance REFRX -12 dB Center Wavelength Range C-RX 840 860 Nm
1)
Conforms to IEEE triple trade-off between center wavelength, RMS spectral width and minimum OMA. Per IEEE 802.3ae, Average Launch Power is informative only. 2) Receiver sensitivity, which is defined for an ideal input signal is informative only.
V. General Specifications Optical Interface Standard Specifications IEEE Std 802.3ae-2002 clause 52, 10GBASE-SR Fibre Channel 10GFC Draft 4.0, 1200-M5-SN-I Fibre Channel 10GFC Draft 4.0, 1200-M5E-SN-I Fibre Channel 10GFC Draft 4.0, 1200-M6-SN-I XPAK MSA 2.3
Minimum Modal Bandwidth at 850 nm (MHz*km) 160 500 200 500 2000 Operating Range 1) (meters) 2 to 26 2 to 66 0.5 to 33 0.5 to 82 0.5 to 300
Standard IEEE Fibre Channel
1)
Fiber Type 62.5 m MMF 50 m MMF 62.5 m MMF 50 m MMF 50 m MMF
Longer reaches possible depending upon link implementation.
(c) Finisar Corporation - November 2007 Rev. B
Page 7
FTLX8551 Product Specification - November 2007
Environmental Performance Operating case temperature: Operating humidity: Fibers and Connectors The transponder has LC receptacles for both Tx and Rx. The transponder is designed for multimode LC cables, 0 polished endface (PC). 70-pin Connector The module interface connector is a 70-pin, printed circuit board edge connection with a 0.5 mm pitch. The appropriate mating connector for the customer PCB is a 70-pin SMT, dual row, right angled, edge connector, 0.5 mm pitch (Tyco Electronics part number 1367337-1, Molex part number 74441-0003 or equivalent). Cage Requirement The cage assembly required to mount the XPAK module is defined by the MSA. Finisar recommends the low profile design -For correct operation and implementation always follow the manufacturer's datasheet. A recommended XPAK rail assembly is Molex part number 74732-0220. Aqueous Wash Finisar XPAK transponders are neither solderable nor aqueous washable and are not intended for these processes. 0C to +70C 0% -95% RH non-condensing
(c) Finisar Corporation - November 2007 Rev. B
Page 8
FTLX8551 Product Specification - November 2007
VI. Regulatory Compliance
Feature ESD: Electrostatic Discharge to the Electrical Pins (HBM) Immunity: Against Electrostatic Discharge (ESD) to the Module Receptacle Immunity: Against Radio Frequency Electromagnetic Field Emission: Electromagnetic Interference (EMI) Standard EIA/JESD22-A114-B (MIL-STD 883D Method 3015.7) EN 61000-4-2 IEC 61000-4-2 Comments Class 1a (> 500 V) Discharges ranging from 2 kV to 15 kV to the front end / faceplate / receptacle cause no damage to module (under recommended conditions). With a field strength of 10 V/m, noise frequency ranges from 10 MHz to 2 GHz. No effect on module performance between the specification limits. Noise frequency range: 30 MHz to 40 GHz Radiated emission does not exceed specified limits when measured with module inside a shielding enclosure with MSA conform cutout. EN 55022 EN 55024 This device complies with part 15 of the FCC Class B Rules1). Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. Must be used in a system housing.
EN 61000-4-3 IEC 61000-4-3 FCC 47 CFR Part 15, Class B EN 55022 Class B CISPR 22 Compliant with 89/336/EEC
FCC:
Eye Safety Finisar FTLX8551 transponders are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Certificate Number Laser Eye FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 9210176-77 Safety 50 Laser Eye TUV EN 60825-1: 1994+A11:1996+A2:2001 R 72052602 Safety IEC 60825-1: 1993+A1:1997+A2:2001 IEC 60825-2: 2000, Edition 2 Electrical TUV EN 60950 R 72052602 Safety Electrical UL/CSA CLASS 3862.07 1439230 Safety CLASS 3862.87
Copies of the referenced certificates will be available at Finisar Corporation upon request.
(c) Finisar Corporation - November 2007 Rev. B
Page 9
FTLX8551 Product Specification - November 2007
VII. DOM Parameters
Parameter Transponder Temperature Monitor Accuracy1) Laser Bias Current Monitor Accuracy2) Transmit Power Monitor Accuracy3) Receive Power Monitor Accuracy
1) 2) 3)
min. -5 -10 -3 -3
Values typ.
max. +5 +10 +3 +3
Unit C % dB dB
0 to 70C case temperature. 0 to 12.5 mA. -1dBm to -3dBm.
VIII. Mechanical Specifications
Parameter Module Retention Force (latch strength) Module Insertion Force Module Extraction Force (with kick-out) Module Extraction Force (without kick-out) 0-80 UNF Screw Torque 1)
1)
Symbol FRET FIN FEXT-K FEXT T0-80 UNF
min. 1 0.84
Values typ. 200 40 16 25
max.
10
Unit N N N N cNm
Two 0-80 UNF screws are used to secure the XPAK module (no bail de-latch version FTLX8551E3S) in the cage. Each XPAK module is shipped with the screws, and assembly is required after the insertion of the module into the cage.
Package Outlines
Figure 2 -XPAK with Bail De-Latch Mechanism
(c) Finisar Corporation - November 2007 Rev. B Page 10
FTLX8551 Product Specification - November 2007
Figure 3 - XPAK with Screw Mount Assembly
IX. References IEEE Std 802.3aeTM-2002 clause 45 & 47 XPAK MSA 2.3
X. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com
(c) Finisar Corporation - November 2007 Rev. B
Page 11

▲Up To Search▲

Price & Availability of FTLX8551E3

	To Download FTLX8551E3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .